0

Solid axle protection

  • Combo-Set Shimano

    81.90 €
    Combo-Set Shimano

    function: Secures the front wheel solid axle oft he Shimano hub dynamo with a M9 x 1 thread and the Shimano rear wheel axis Alfine or Nexus with a 3/8 inch thread. A closure fort he front and the back each. Since the outer coding ist the same both nuts can be opened with the same Pit-key. content: 1 closure M9  x 1, 1 closure 3/8 inch, 1 Pit-key for solid axles, 2 code cards  installation guide (solid axles) important: The protruding thread is supposed to stick out of the dropout for approximately 14mm. The locking ring requires a space (supporting surface) of 15 mm in the radius or rather 30 mm in the diameter around the thread, so that the Pitlock lock can be installed safely. attention: The two Pitlock systems for quick releases and for solid axles possess two different measurements. Due to the different thread sizes the keys of the two Pitlock systems are not combinable. The closures for M5 and M6 are a lot smaller than those of the “thick” solid axles. Our solid axle systems are combinable! So, if you have a Shimano solid axle dynamo hub on your front wheel and a Rohloff solid axle or a Shimano Alfine/ Nexus on your rear wheel, it is possible to secure these two hubs with the same coding.

  • Set M10 Double

    81.90 €
    Set M10 Double

    ROHLOFF SOLID AXLES Axle plate TS OEM / Rohloff No.: 8235L Thanks to numerous suggestions from our customers and support from Rohloff we have been able to expand our product range and are now able to offer you a Pitlock locking device for the Rohloff solid axles. If wide aluminum dropouts are installed on your bicycle, we recommend using the Pitlock M10 / Mono set, that secures one side of the Pitlock solid axles. The M10/ double set contains two locks and can therefore be installed on both sides of the Rohloff solid axles.   content: 2 closures M10, 1 Pit key for solid axles, 1 code card to installation instructions   important: The protruding thread is supposed to stick out of the dropout for approximately 14mm. The locking ring requires a space (supporting surface) of 15 mm in the radius or rather 30 mm in the diameter around the thread, so that the Pitlock lock can be installed safely. In case the protruding thread is too short, it is necessary to use an axle stub with a long threaded axle (available from Rohloff, article no.: 8235L Axle Plate TS OEM). attention: The two Pitlock systems for quick releases and for solid axles possess two different measurements. Due to the different thread sizes the keys of the two Pitlock systems are not combinable. The closures for M5 and M6 are a lot smaller than those of the “thick” solid axles. Our solid axle systems are combinable! So, if you have a Shimano solid axle dynamo hub on your front wheel and a Rohloff solid axle or a Shimano Alfine/ Nexus on your rear wheel, it is possible to secure these two hubs with the same coding.

  • Set M10 Single

    54.90 €
    Set M10 Single

    ROHLOFF SOLID AXLES Axle plate TS OEM / Rohloff No.: 8235L Thanks to numerous suggestions from our customers and support from Rohloff we have been able to expand our product range and are now able to offer you a Pitlock locking device for the Rohloff solid axles. If wide aluminum dropouts are installed on your bicycle, we recommend using the Pitlock M10 / Mono set, that secures one side of the Pitlock solid axles. The M10/ double set contains two locks and can therefore be installed on both sides of the Rohloff solid axles.   Secures the rear wheel axle of the Rohloff solid axle by using a M10 x 1 thread.   content: 1 closure M10, 1 Pit key for solid axles, 1 code card installation guide (solid axles) important: The protruding thread is supposed to stick out of the dropout for approximately 14 mm. The locking ring requires a space (supporting surface) of 15 mm in the radius or rather 30 mm in the diameter around the thread, so that the Pitlock lock can be installed safely. In case the protruding thread is too short, it is necessary to use an axle stub with a long threaded axle (available from Rohloff, article no.: 8235L Axle Plate TS OEM). attention: The two Pitlock systems for quick releases and for solid axles possess two different measurements. Due to the different thread sizes the keys of the two Pitlock systems are not combinable. The closures for M5 and M6 are a lot smaller than those of the “thick” solid axles. Our solid axle systems are combinable! So, if you have a Shimano solid axle dynamo hub on your front wheel and a Rohloff solid axle or a Shimano Alfine/ Nexus on your rear wheel, it is possible to secure these two hubs with the same coding.

  • Set SH38 Double

    81.90 €
    Set SH38 Double

    function: Secures the front wheel solid axle of the Shimano hub dynamo by using a M9 x 1 thread. There is a closure for the left and the right each. content: 2 closures 3/8 inch, 1 Pit key for solid axles, 1 code card installation guide (solid axles) important: The protruding thread is supposed to stick out of the dropout for approximately 14mm. The locking ring requires a space (supporting surface) of 15 mm in the radius or rather 30 mm in the diameter around the thread, so that the Pitlock lock can be installed safely. attention: Both Pitlock systems for quick-releases and for solid axles have two different measurements. Due to the different thread sizes the keys of the two Pitlock-systems are not combinable. The closures for M5 and M6 are significantly smaller than the “thick” solid axles. Our solid axle systems are combinable among each other! So if you have a Shimano solid axle dynamo on your front wheel and a Rohloff solid axle or a Shimano Alfine/ Nexus on your rear wheel, these two hubs can be secured with the same coding.

  • Set Sh38 Single

    54.90 €
    Set Sh38 Single

    function: Secures the rear wheel solid axle of the Shimano hub Alfine or Nexus with a 3/8 inch thread. It is a closure for one side.  content: 1 closure 3/8 inch, 1 Pit key for solid axles, 1 code card installation guide (solid axles) important: The protruding thread is supposed to stick out of the dropout for approximately 14mm. The locking ring requires a space (supporting surface) of 15 mm in the radius or rather 30 mm in the diameter around the thread, so that the Pitlock lock can be installed safely. attention: Both Pitlock systems for quick-releases and for solid axles have two different measurements. Due to the different thread sizes the keys of the two Pitlock-systems are not combinable. The closures for M5 and M6 are significantly smaller than the “thick” solid axles. Our solid axle systems are combinable among each other! So if you have a Shimano solid axle dynamo on your front wheel and a Rohloff or Shimano Alfine/ Nexus solid axle on your rear wheel, these two hubs can be secured with the same coding. 

  • Set SH90 Double

    81.90 €
    Set SH90 Double

    function: Secures the front wheel solid axle of the Shimano hub dynamo by using a M9 x 1 thread. There is a closure for the left and the right each. content: 2 closures M9 x 1, 1 Pit key for solid axles, 1 code card installation guide (solid axle) important: The protruding thread is supposed to stick out of the dropout for approximately 14mm. The locking ring requires a space (supporting surface) of 15 mm in the radius or rather 30 mm in the diameter around the thread, so that the Pitlock lock can be installed safely. attention: Both Pitlock systems for quick-releases and for solid axles have two different measurements. Due to the different thread sizes the keys of the two Pitlock-systems are not combinable. The closures for M5 and M6 are significantly smaller than the “thick” solid axles. Our solid axle systems are combinable! So if you have a Shimano solid axle dynamo on your front wheel and a Rohloff solid axle on your rear wheel or if you have a Shimano Alfine/ Nexus, these two hubs can be secured with the same coding. 

  • Set SH90 Single

    54.90 €
    Set SH90 Single

    function: Secures the front wheel solid axle of the Shimano hub dynamo by using a M9 x 1 thread. A closure for one side. content: 1 closure M9 x 1, 1 Pit key for solid axles, 1 code card installation guide (solid axles) important: The protruding thread is supposed to stick out of the dropout for approximately 14mm. The locking ring requires a space (supporting surface) of 15 mm in the radius or rather 30 mm in the diameter around the thread, so that the Pitlock lock can be installed safely.  attention: Both Pitlock systems for quick-releases and for solid axles have two different measurements. Due to the different thread sizes the keys of the two Pitlock-systems are not combinable. The closures for M5 and M6 are significantly smaller than the “thick” solid axles. Our solid axle systems are combinable! So if you have a Shimano solid axle dynamo on your front wheel and a Rohloff solid axle or a Shimano Alfine/ Nexus on your rear wheel, these two hubs can be secured with the same coding.

SOME OF OUR PRODUCTS
  • lock for frot wheel and seat post, M6 screw and aluminium plug for securing the ahead system, 1 PIT key, 1 code card ATTENTION !!! Repurchase of coded parts is only possible with a code number (on the ccode card) !!! To the installation guide When installing the seat post security, please make sure that the outer pressure surfaces of the saddle clamp are plane as well as parallel. If this is ot the case, you can order one of our saddle clamps. To the Pitlock saddle clamps Our sets commonly contain standard lengths: front wheel lock 119 mm installation width seat post lock 33 mm installation width M6 coded crew 32 mm installation width aluminium plug 1 1/8 inch (available in silver or black) The following specal lengths are available for our sets: front wheel lock 130 mm installation width seat post lock 23 mm/ 45 mm /60 mm installation width These special lengths are available for our sets without any extra charge. Please tell us your preferred special length at the end of your order, in the field "your message to us". If none of these special lengths fits, you still have the opportunity to use our universal skewer. The skewer's diameter is 5 mm. M6 code bolts have 6 mm diameter. What is the installation width?

  • function: Secures the front wheel solid axle of the Shimano hub dynamo by using a M9 x 1 thread. There is a closure for the left and the right each. content: 2 closures 3/8 inch, 1 Pit key for solid axles, 1 code card installation guide (solid axles) important: The protruding thread is supposed to stick out of the dropout for approximately 14mm. The locking ring requires a space (supporting surface) of 15 mm in the radius or rather 30 mm in the diameter around the thread, so that the Pitlock lock can be installed safely. attention: Both Pitlock systems for quick-releases and for solid axles have two different measurements. Due to the different thread sizes the keys of the two Pitlock-systems are not combinable. The closures for M5 and M6 are significantly smaller than the “thick” solid axles. Our solid axle systems are combinable among each other! So if you have a Shimano solid axle dynamo on your front wheel and a Rohloff solid axle or a Shimano Alfine/ Nexus on your rear wheel, these two hubs can be secured with the same coding.

  • content: 2 x M6 code bolts, 2 security rings, 2 teflon washers, 4 flat washers,1 PIT key and code card to secure rim or disc brakes, lampholder or pinion gear.      

  • Secures: Front wheel (installation width = 119 mm standard) Rear wheel (installation width = 155 mm standard) Seat post (installation width = 33 mm standard) + Securing Ahead system in black or silver + Securing calliper brake M6 code bolts have 6 mm diameter.1 Pit with code pass